產品分類 更多>>
【產品名稱】礦山專用橡膠輸送帶nn100 650寬 10mm厚
【布層】3-8層均可定制
【厚度】6.5-20mm均可定制
【型號】 650*5（3 1.5）
根據覆蓋膠性能不同分為耐寒型、耐酸型、耐堿型、耐油型、耐磨型等.
根據用途的不同可以分為提升帶、動力帶、輸送帶。
根據結構的不同可以分為普通疊層式、加橫向增強層的抗沖擊、防撕裂型。
《規格》
（1）帶芯材質：NN100、NN150、NN200、NN250、NN300、NN350、NN400、NN450、NN500
（2）帶寬：100mm-3000mm
（3）布層：1－10層
（4）覆蓋膠：工作面：1.5-8.0mm非工作面：1.5-4.5mm
特點：帶體薄、強力高、耐沖擊、性能好、層間粘合強度大、屈撓性優異及使用壽命長等特點，適合中長距離、較高載量高速條件下輸送物料。
型號：NN80、NN125、NN100、NN150、NN200、NN300、NN400
普通型符合標準：GB／T7984－2001
一般難燃型符合標準：GB／T10822－89
規格：①帶寬：100mm-3000mm ②布層：2－8層 ③覆蓋膠：工作面：1.5-8mm 非工作面：0mm-4.5mm。
《Variety》
According to different rubber covering performance is divided into cold, acid, alkali resistant, oil resistant, wear resistant, etc.
According to different purposes of can be divided into elevator belt, belt, conveyor belt.
Depending on the structure can be divided into ordinary laminated type, and lateral impact resistant, laceration resistant enhancement layer.
《Specifications》
Material:
(1) with core NN100, NN150, NN200, NN250, NN300, NN350, NN400, NN450, NN500
(2) the bandwidth: 100 mm - 3000 mm
(3) layers: 1-10 layer
(4) cover gum: face: 1.5 8.0 mm not face: 1.5 to 4.5 mm
Characteristic: the thin belt body, high strength, impact resistance, good performance, interlayer adhesion strength, excellent flexing and long service life, etc, suitable for long distance, high capacity under the condition of high speed conveying material.
Model: NN80, NN125, NN100, NN150, NN200, NN300, NN400
Normal standard: GB/T7984-2001
General type flame retardant standard: GB/T10822-89
Specification: (1) bandwidth: 100 mm - 3000 mm (2 layers: 2-8 layer (3) rubber cover: face: 1.5 8 mm not face: 0 mm to 4.5 mm.
《輸送帶接頭方法》《The conveyer belt joint method》
所有的輸送帶必須接成環形才能使用，所以輸送帶接頭的好壞直接影響輸送帶的使用壽命和輸送線能否平穩順暢地運行。一般輸送帶接頭常用方法有機械接頭、冷粘接接頭、熱硫化接頭等。
All of the conveyor belt must meet a ring to use, so the stand or fall of conveyor belt joint can directly affect the service life of the conveyor belt and conveyor line smooth running smoothly. Methods general conveyor belt joint with mechanical joints, cold, hot vulcanizing bonding joint joint, etc.
《尼龍輸送帶保養與維護》《The nylon conveyor belt maintenance and maintenance》
1、輸送膠帶在運輸和貯存中，應保持清潔避免陽光直射或雨雪浸淋,防止與酸、堿、油類、有機溶劑等物質接觸，并距離發熱裝置一米以外。
2、貯存時倉庫溫度宜保持一18-40℃之間，相對濕度宜保持在50- 80％之間。
3、貯存期間，產品須成卷放置，不得折迭，放置期間應每季翻動一次。
4、不同類型、規格層數的輸送帶不宜接在一起使用，其接頭較好采用膠接法。
5、輸送膠帶的類型、結構、規格、層數應根據使用條件合理選用。
6、輸送膠帶運行速度一般不宜大于2．5米／秒，塊度大，磨損性大的物料和使用固定梨的卸料裝置應盡量采用低速。
7、運輸機的傳動滾筒直徑與輸送帶布層的關系、傳動滾筒、改向滾筒的配套以及對托輥槽角的要求應根據運輸機的設計規定，合理選取。
8、給料方向應順膠帶的運行方向，為減小物料下落時對膠帶的沖擊應采溜槽，減小物料下落距離；膠帶受料段應縮短托輥間距和采用緩沖托輥為漏料，帶順應采用柔軟適度的擋料板，以免檔料板過硬，刮破輸送帶的帶面。
9、輸送帶在使用中應注意以下事項：①避免托輥被物料覆蓋，造成回轉不靈，防止漏料卡于滾筒與膠帶之間，注意活動部分的潤滑，但不得油污輸送膠帶；②避免帶負荷啟動；③膠帶發生跑偏，應用時采取措施糾正；④發現膠帶局部損人造棉應用時修補，以免擴大；
1, in transportation and storage, the belt should be kept clean and avoid direct sunlight or snow and rain leaching leaching, prevent from acid, alkali, oil, organic solvents, such as physical contact, and distance from the heating device one meter away.
2, storage warehouse temperature should keep a between 18 to 40 ℃, relative humidity should be kept between 50-80%.
3, during storage, the product must be placed in rolls, folding, should be placed during quarterly turn once.
4, layer number of different types and specifications of the conveyor belt should not be connect together to use, its connection with glue joint is best.
5, belt type, structure, specification and layer should be selected according to conditions of use reasonable.
6, conveyor belt running speed should not be commonly more than 2.5 m/s, big pieces, abrasion resistant materials and using fixed pear discharging device should be used as far as possible at low speed.
7, conveyor drive roller conveyor belt and the diameter of the relationship between layers, drive roller, redirection roller and the requirement for roller groove Angle should be prescribed according to the design of the conveyor, reasonable selection.
8, the feeding direction should be along the belt running direction, to reduce the material impact to tape down shall adopt chute, reduce material falling distance; Tape by material paragraph should shorten the roller, buffer roller spacing and used for the material leakage, take to use soft moderate keep-off board, in order to avoid gear plate quality, scraping the broken conveyor belt surface.
9, conveyer belt in use should be paid attention to the following: (1) avoid rollers is covered by the material, causing rotation is ineffective, prevent leakage of material between the roller and the tape, pay attention to the lubrication activities section, but not the oil conveying belt; (2) avoid loading starts; (3) belt running deviation, application to take steps to correct; (4) found that the local loss of viscose tape application repair, lest expanding;
《尼龍輸送帶跑偏的原因》《The cause of the nylon conveyor belt running deviation》
在使用過程中，如果出現跑偏，則要作以下檢查以確定原因，進行進行調整。輸送帶跑偏時常檢查的部位和處理方法有：
（1）檢查托輥橫向中心線與帶式輸送機縱向中心線的不重合度。如果不重合度值超過3mm，則應利用托輥組兩側的長形安裝孔對其進行調整。具體方法是輸送帶偏向一側，托輥組的一側向輸送帶前進的方向前移，或另外一側后移。
（2）檢查頭、尾機架安裝軸承座的兩個平面的偏差值。若兩平面的偏差大于1mm，則應對兩平面調整在同一平面內。頭部滾筒的調整方法是：若輸送帶向滾筒的右側跑偏，則滾筒右側的軸承座應當向前移動或左側軸承座后移；若輸送帶向滾筒的左側跑偏，則滾筒左側的軸承座應當向前移動或右側軸承座后移。尾部滾筒的調整方法與頭部滾筒剛好相反。
（3）檢查物料在輸送帶上的位置。物料在輸送帶橫斷面上不居中，將導致輸送帶跑偏。
如果物料偏到右側，則皮帶向左側跑偏，反之亦然。在使用時應盡可能的讓物料居中。為減少或避免此類輸送帶跑偏可增加擋料板，改變物料的方向和位置。
In use process, if there is a running deviation, and then to make the following checks to determine the reason, to adjust. The conveyor belt running deviation often check the location and treatment methods are:
(1) check the roller center line of the transverse and longitudinal center line of belt conveyor is not coincidence degree. Value is more than 3 mm, if you don\
