2014.06.14 Shanghai kai rich industrial co., LTD. (p20 steel sales http://www.xfmjgy.cn information: in the feed line technology production of nodular cast iron, on the basis of theoretical analysis, through the analysis of the original into the production method of CAM shaft when the cause of the problem, the feed production line technology is verified the rationality and feasibility of FCD700 ductile iron camshaft, and develop the technology to replace the original into feed line method is used to process in the production of FCD700 ductile iron camshaft, and through the industrial test of test samples collected in the process of spectral analysis, tensile samples, metallographic specimen, and analyzes the experimental data. Shanghai kai rich industrial co., LTD. (p20 steel sales http://www.xfmjgy.cn industrial test results show that the FCD700 ductile iron camshaft was produced by feeding line technology, spheroidizing rate, the size of the graphite ball casting is better than the original into process parameters such as grade, and highly improve the stability of the mechanical properties of castings, spheroidizing treatment effect is stable and good reproducibility; Feed line technology of hot metal silicon increasing quantity is small, can use a lot of burden, reduce the production cost, and can be flexibly adjusted pressure casting machine in magnesium residual fluctuations; While feeding line process which eliminated spheroidizing in flue gas, in large part's impact on the environment and pollution, reduces the labor intensity of workers. 　　2014.06.14上海偕富實業有限公司（p20模具鋼http://www.xfmjgy.cn銷售）資訊：在對喂線技術工藝生產球墨鑄鐵進行理論分析的基礎上，通過分析原沖入法工藝生產凸輪軸時存在問題的原因，驗證了喂線技術生產FCD700球墨鑄鐵凸輪軸的合理性及可行性，進而制定出了采用喂線技術工藝替代原有沖入法工藝生產FCD700球墨鑄鐵凸輪軸的方案，并進行了工業化試驗，試驗過程中采集了光譜分析試樣、拉伸試樣、金相試樣，并對試驗數據進行了整理分析。 上海偕富實業有限公司（p20模具鋼http://www.xfmjgy.cn銷售）的工業化試驗結果表明：采用喂線工藝生產FCD700球墨鑄鐵凸輪軸時，鑄件球化率、石墨球尺寸等級等參數都優于原沖入法工藝，且鑄件力學性能的穩定性得到很大改善，球化處理效果穩定，重現性好；喂線技術工藝對鐵水增硅量小，可大量使用回爐料，降低了生產成本，并能靈活調整氣壓澆注機內鎂殘量的波動；同時喂線處理工藝在很大程度上消除了球化作業時煙氣對環境的影響和污染，降低了工人勞動強度。